Electrical Engineering Intern
QOSMIC · Bengaluru, Karnataka, India
Posted 20 Nov 2026 · Full-time
Type: Internship, 3–6 months | B.Tech/M.Tech students and recent graduates
Location: Bengaluru (on-site)
Stipend: INR 35,000 per month
Joining Date: Immediate
About the Role
We're building the optical highway to the cosmos
Join us as an Electrical Engineering Intern and own real hardware end to end. You will take a board for our optical communication terminals from idea to validated hardware yourself: design the power and analog circuits, simulate them, lay out the PCB, assemble and bring it up, write the firmware, debug it on the bench, and prove it meets its specification. The work spans power distribution and protection, precision analog and driver electronics, and the microcontroller code that controls and monitors them. This is a 3–6 month, on-site internship for students who have already built and broken real hardware and want to do it properly, with mentorship from the core electronics team.
Responsibilities
● Design power circuits: DC-DC converters and LDOs, load switches and eFuses, current sensing, reverse-polarity, over-voltage and over-current protection, and rail sequencing
● Design analog circuits: op-amp signal conditioning, instrumentation and difference amplifiers, active filters, voltage references, regulated current and voltage sources, and ADC and DAC front ends
● Simulate both in LTspice — load transients, inrush, protection response, op-amp stability and phase margin, filter response, and noise — and check every simulation against bench measurement
● Capture schematics and lay out PCBs in Altium or KiCad: component selection, grounding and return paths, separation of power and sensitive analog sections, current-carrying copper, thermal design, decoupling, and manufacturing outputs
● Assemble and bring up your own boards: hand soldering and SMD rework, staged power-up on a current-limited supply, rail verification, and systematic fault isolation
● Write embedded C on STM32 to run and test the hardware: ADC sampling, DAC output, PWM, timers, GPIO control of switches and enables, and UART, I²C or SPI communication
● Debug hardware and firmware together with an oscilloscope and logic analyser: probe signals, decode serial buses, measure timing, ripple and noise, and use SWD to step through code on target
● Validate against specification: efficiency, ripple, line and load regulation, transient response, protection trip points, gain and bandwidth, offset, noise floor, linearity, and thermal performance — with data logged and analysed in Python or MATLAB
● Build the test setups you need: jigs, breakout boards, electronic-load arrangements, and harnesses
● Run pre-compliance EMI/EMC checks, and document designs, calculations, test procedures and results clearly enough that someone else can pick up the work
Requirements
● Pursuing or recently completed a B.Tech/M.Tech in Electrical, Electronics, ECE, or Instrumentation Engineering
● Real hands-on hardware: you have designed, built and debugged boards yourself — not only simulated them or followed a tutorial
● Analog fundamentals: op-amps (gain-bandwidth, slew rate, offset, noise, stability), filters, references, current sensing, and how ADC and DAC resolution, sampling and reference choice affect a measurement
● Power fundamentals: linear versus switching regulators, common converter topologies, inductor and capacitor selection, ripple, efficiency, thermal dissipation, and protection
● PCB design: at least two boards taken through schematic, layout, fabrication, and bring-up
● Embedded C on STM32 or similar microcontrollers: configuring peripherals, reading datasheets and reference manuals to get them working, and debugging on target
● Bench skills: hand soldering including fine-pitch SMD and rework, and confident use of an oscilloscope, DMM, and bench supply
● Tools you should already use or pick up quickly:
– Simulation: Ltspice and Ngspice
– PCB design: Altium Designer or KiCad
– Firmware: Embedded C, C and C++ (STM32CubeIDE or a GCC/Make toolchain, with an ST-Link or J-Link debugger)
– Bench: oscilloscope, logic analyser, DMM, programmable power supply, electronic load, function generator, soldering station, and hot-air rework
– Analysis and version control: Python or MATLAB, and Git (version control)
● Comfortable going deep into datasheets, reference manuals and application notes when something does not behave
● Awareness of IPC standards for PCB design and assembly, component derating, basic EMI/EMC layout practice, and safety around power and batteries
● Clear communication, honest reporting of what worked and what did not, and the drive to learn fast
Nice-to-Have
● Experience on a student engineering team: rocketry, SAE BAJA, Formula Student, solar or electric vehicle, CubeSat, or robotics
● Battery packs, BMS, motor drives, or power distribution units built for a real vehicle or system
● Low-noise or precision analog design, or closed-loop analog control
● Harness design, crimping, and connector selection for vibration-prone environments
● Exposure to space, defence, or automotive standards and environmental testing
What We Offer
● Your own designs built, tested, and used on flight-bound hardware
● World-class lab facilities and test equipment, with mentorship from the core electronics team
● Potential for extension or a full-time role based on performance
● Collaborative multi-disciplinary research environment
How to Apply
- Send your resume and a brief note about your interests to: careers@qosmic.space. Include photos, schematics, or repositories of hardware you have built, and a few lines on one thing that went wrong on a real board and how you found and fixed it.