Project Associate - Electrical

QOSMIC · Bengaluru, Karnataka, India

Posted 20 Nov 2026 · Full-time

Apply on LinkedIn

Type: Full Time, Fixed Term (6 –12 months) | 0–2 years Work Experience

Location: Bengaluru (on-site)

Compensation (CTC): Determined by the candidate’s qualifications and relevant experience

Joining Date: Immediate


About the Role:


We're building the optical highway to the cosmos

Join us as a Project Associate in Electrical on one of our core hardware programmes. You will design, simulate, build, debug and test the electronics inside our optical communication terminals – precision drive and sensing circuits, power supplies, and the microcontroller firmware that brings them to life. This is a fixed-term role of 6–12 months, with extension or conversion to a permanent position based on performance and programme needs. It suits a recent B.Tech or M.Tech graduate who wants real hardware, real debugging, and real ownership from the first week.


Responsibilities

● Design and simulate analog circuits in LTspice: op-amp signal chains, sensor front ends, instrumentation amplifiers, active filters, and actuator driver stages

● Design and verify power electronics: buck, boost and flyback converters, LDOs, auxiliary and bias supplies, rail sequencing, current limiting, and protection

● Capture schematics and lay out PCBs in Altium and KiCad: component selection, stack-up, grounding and return paths, partitioning of analog, digital and power sections, clearance, decoupling, and manufacturing outputs

● Bring up and debug boards: staged power-up, rail verification, soldering and rework, and systematic fault isolation with oscilloscopes, logic analysers, DMMs, and current-limited supplies

● Write and debug embedded C firmware on STM32 for bring-up and test: GPIO, timers, ADC and DAC, SPI, I²C, UART, and DMA

● Characterise circuits and subsystems: frequency and step response, noise floor, linearity, drift with temperature, and driver performance limits, with data logged and analysed in Python or MATLAB

● Support closed-loop system testing with the team: calibration, system identification, and tuning experiments

● Run pre-compliance EMI/EMC and environmental checks — conducted and radiated emissions, susceptibility, ESD, and thermal — and fix what they find

● Build test jigs, harnesses, interface boards (RS-422/485, SPI, CAN), and hardware-in-the-loop setups

● Document designs, test procedures and results, present at design reviews, and keep all design files under version control


Requirements

● B.Tech/M.Tech in Electrical, Electronics, ECE, or Instrumentation Engineering; 0–2 years of experience, where strong project or internship work counts

● Analog fundamentals: op-amps (gain-bandwidth, slew rate, offset, noise, stability), filters, and amplifier design for sensors and actuators

● Data converters: solid understanding of ADCs and DACs – resolution, sampling, aliasing, references, settling, and how converter choice affects a measurement or control loop

● Power electronics fundamentals: linear versus switching regulators, common converter topologies, magnetics and capacitor selection, ripple, efficiency, thermal dissipation, and protection

● Circuit simulation in LTspice: transient, AC, noise, and stability analysis, and the judgement to know when a model can be trusted

● PCB design in Altium and KiCad: multiple boards taken through schematic, layout, fabrication, and bring-up

● Board-level debugging: SMD soldering and rework, oscilloscopes and logic analysers, and a methodical approach to isolating faults

● Embedded C on STM32 or similar ARM Cortex-M parts, from HAL to register level, with on-target debugging over SWD

● Interfaces: SPI, I²C, UART, and working knowledge of RS-422/485 and CAN

● Tools you should already use or pick up quickly:

– Simulation: Ltspice and Ngspice

– PCB design: Altium Designer or KiCad

– Firmware: Embedded C, C and C++ (STM32CubeIDE or a GCC/Make toolchain, with an ST-Link or J-Link debugger)

– Bench: oscilloscope, logic analyser, DMM, programmable power supply, electronic load, function generator, soldering station, and hot-air rework

– Analysis and version control: Python or MATLAB, and Git (version control)

● Not afraid to go deep into datasheets, reference manuals and application notes, and to work from them to a design that holds up on the bench

● EMI/EMC awareness: noise sources and coupling paths, filtering, shielding, and layout practice; IPC standards for PCB design and assembly; component derating

● Python or MATLAB for data analysis and plotting

● Clear documentation, honest reporting of results, and the drive to learn fast


Nice-to-Have

● Precision motion control or positioning systems, and driving reactive loads such as motors or actuators

● Low-noise sensing and signal conditioning for precision measurement

● Control systems basics: PID, Bode plots, loop stability, and filtering

● Exposure to optical or photonic systems

● Space or defence hardware exposure: vibration and thermal testing, or NASA, ECSS, and MIL-STD standards

● Student satellite, rocketry, or robotics team experience, or personal hardware projects you can show

What We Offer

● Hands-on ownership of flight-bound hardware, from bench prototype to qualification

● World-class lab facilities and test equipment, with mentorship from the core electronics team

● A clear path to extension or full-time conversion based on performance

● Collaborative multi-disciplinary research environment


How to Apply

Send your resume and a brief note about your interests to: careers@qosmic.space. Include links to boards, schematics, or code you have built.